Contact Us Now
GET SOCIAL
-
The replacement cycle of wiper blades is generally about a year, mainly depending on the frequency of use, and remember to clean the wiper blades with a towel after each rain, which not only increases the service life but also protects the glass. -
Car fuel pressure regulators can affect idle speed. It will cause idling jitter, poor acceleration, and even flameout. At the same time, fuel consumption will increase. The fuel pressure regulator must be replaced in time. -
For Engine Model GWM 4D20. Looking for TurboCharger, Super Charger, turbosuperchager for other model, please contact our sales manager Now. Whatsapp:008617503319627 Tel: 008617503319627 Email: [email protected] -
Timing Gear Housing For 2.8TC Engine -
The timing belt is an important part of the engine's air distribution system. It is connected with the crankshaft and matched with a certain transmission ratio to ensure the accuracy of the intake and exhaust time. The use of belts rather than gears for transmission is because belts are less noisy, less variable and easier to compensate for. Obviously, the life of the belt must be shorter than that of the metal gear, so the belt should be replaced regularly. -
Symptoms of a broken  tie rod end mainly include the following conditions. First, if the tie rod end of the front wheel of the car is broken, the following symptoms will appear: the road section is bumpy, thump, thump; the car is unstable, swaying left and right; braking deviation; direction failure. The second is that the tie rod end is too wide, and it is easy to break when subjected to impact load. Repair as soon as possible to avoid danger. -
T thermostat assembly is a valve that controls the coolant flow path. It is an automatic temperature adjustment device, usually containing a temperature sensing component, which turns on and off the flow of air, gas or liquid by thermal expansion or cold contraction. -
The stabilizer bar, also known as the anti-roll bar and the balance bar, is an auxiliary elastic element in the automobile suspension. The function of the anti-roll bar is to prevent the body from leaning excessively when cornering and to improve the driving stability of the car on uneven roads. -
The shallow oil pan is the lower half of the crankcase, also known as the lower crankcase. The function is to close the crankcase as the casing of the oil storage tank, prevent impurities from entering, and collect and store the lubricating oil flowing back from the friction surfaces of the diesel engine, dissipate part of the heat, and prevent the oxidation of the lubricating oil. -
1) According to the operating regulations, avoid the clutch from being half-engaged and half-disengaged, and reduce the number of times the clutch is used. 2) Pay attention to maintenance, and use the cooking method to soak the butter so that it has sufficient lubricant during regular or annual inspection and maintenance. 3) Pay attention to leveling the clutch release lever to ensure that the elastic force of the return spring meets the regulations. 4) Adjust the free stroke to meet the requirements (30-40mm) to prevent the free stroke from being too large or too small. 5) Minimize the times of joining and separating, and reduce the impact load. 6) Step lightly and easily to make it engage and disengage smoothly. -
Sale!
The brake shoe is the friction couple of the drum brake. In addition to the strength and rigidity required as a component, it should also have a friction coefficient as high and stable as possible, as well as appropriate wear resistance, heat resistance and heat dissipation. and heat capacity, etc. -
In a high temperature working environment, the engine must be properly cooled to keep it working at a suitable temperature to meet the requirements of good engine performance, durability and exhaust emissions. The engine cooling system plays a key role here. Includes critical cooling fans, water tanks, thermostats, and more. -
Car radiators usually refer to engine radiators. The radiator consists of three parts: the water inlet chamber, the water outlet chamber, the main piece and the radiator core. The coolant acts in the radiator core, and the air passes through the radiator core. The hot coolant is cooled by dissipating heat to the air, and the cold air is warmed by receiving heat from the coolant, so the radiator is a heat exchanger. -
Plastic Buckle 09630001 is a mechanism used for embedded connection or integral locking of one part and another part, usually used for the connection of plastic parts, and its material is usually composed of plastic material with certain flexibility. The biggest feature of the snap connection is that it is easy to install and disassemble, and it can be disassembled without tools. Now the snap connection technology has been widely used in the connection of automotive interior parts -
Piston rings are metal rings that are embedded in the grooves of the piston. There are two types of piston rings: compression rings and oil rings. The compression ring is used to seal the combustible mixture in the combustion chamber; the oil ring is used to scrape excess oil from the cylinder. -
The main function of the oil pan 1009100-EG01Â is to store oil (lubricating oil) and close the crankcase. The oil pan bears little force and is generally stamped from a thin steel plate. Its shape is determined by the general arrangement of the engine and the capacity of the oil. -
The function of the oil filter is to filter out the sundries, gums and moisture in the oil, and deliver clean oil to each lubricating part. -
The shock absorber is a vulnerable part during the use of the car. The performance of the shock absorber will directly affect the driving stability of the car and the life of other parts. Therefore, the shock absorber should always be in good working condition. After determining that the shock absorber has a problem or fails, first check whether the shock absorber leaks oil or has signs of old oil leakage. -
Intercoolers are usually found on turbocharged cars. Because the intercooler is actually a supporting part of the turbocharger, and its function is to improve the ventilation efficiency of the turbocharged engine. -
The high pressure fuel pump is the interface between the high-pressure fuel circuit and the low-pressure fuel circuit. Its function is to generate fuel pressure in the common rail pipe by controlling the fuel output. In all operating conditions, it is mainly responsible for providing sufficient high-pressure fuel to the common rail. -
Sale!
The fuel filter element is used to filter out the sundries in the fuel. The alias is the oil-water separator and the diesel fine filter, which is a microporous paper filter element. In the early days, the filter elements of gasoline filters were metal sheet slot type, metal filter mesh type, nylon cloth type, porous ceramic type and so on. -
Gasoline filters and diesel filters are generally made of microporous paper filter elements, which are treated with phenolic resin and made into a folded cylinder type, which has the advantages of good passing performance, high filtration efficiency, simple structure, low cost, and easy maintenance. -
FUEL FILLER: Due to strict regulations on gasoline evaporation, the requirements for low fuel permeability are increased. Therefore, DAI-EL with good low fuel permeability is applied to the fuel pipe of automobile. -
Front Mount Bracket For GW4G15 Engine -
In addition to being beautiful, the biggest role of the front bumper grille is to intake air and reduce air resistance. The greater the impact of the front grille on the resistance of the engine compartment, the resistance of the engine compartment accounts for about 10% of the total resistance, and the active closing of the grille is conducive to reducing the resistance in the engine compartment. In addition, the front bumper grille also plays a role in cooling. The front grille is the passage between the outside world and the engine compartment, through which the air enters the engine compartment, takes away the heat of the radiator, and cools it down. -
The plastic bumper is composed of three parts: the outer plate, the buffer material and the beam. The outer plate and buffer material are made of plastic, and the beam is stamped with a cold-rolled sheet with a thickness of about 1.5 mm to form a U-shaped groove; the outer plate and buffer material are attached to the beam, and the beam and the frame longitudinal beam are screwed together, which can be used at any time. Remove it. The plastic used in this plastic bumper is generally made of polyester and polypropylene. -
Sale!
For Model Wingle 5 CC1031PS7A. Looking for wiper motor for other model, please contact our sales manager Now. Whatsapp:008617503319627 Tel: 008617503319627 Email: [email protected] -
The drive axle needs to be replaced when the half shaft is aged, cracked, bent and more serious abnormal noise. The drive axle is the rotating shaft that connects the wheel and the transfer case, and is one of the main components of the transmission. Although the half shaft is not easy to be damaged in normal times, it is best to check the half shaft every 10,000 kilometers. The key is to check whether the half shaft oil seal has the problem of aging or lack of oil. -
The fender is the outer panel of the body that covers the wheel, just like a bicycle shell, it has the functions of protecting the tire and mud, because the shape and position of the part of the body are named after the bird's wing. -
Expansion tank is a small tank used to protect closed (not open to atmospheric pressure) water heating systems and domestic hot water systems from overpressure. The tank is partially filled with air, and its compressibility cushions the shock caused by water hammer and absorbs excess water pressure caused by thermal expansion. -
Engine Mount Bracket For H6 COUPE -
Engine Mount Assy For GWM Wingle 5 -
Engine Maintenance Kit For GW 4D20 -
Cylinder Head For 4G15B -
The cylinder head belongs to the valve mechanism in the internal combustion engine, and is mainly used to close the upper part of the cylinder to form the combustion chamber. In addition, it also serves as the support of the camshaft and the rocker shaft as well as the intake and exhaust pipes, mainly to suck the air into the cylinder, the spark plug ignites the combustible mixture, drives the piston to do work, and the exhaust gas is discharged from the exhaust pipe.
-
Cylinder For GW4G15 -
The clutch pressure plate is one of the important components of the clutch, which can press the clutch driven plate to the flywheel, transmit the engine torque, and vice versa, control the rotation of the driven plate. -
Clutch Disk For GWM 4D28 Engine -
Carbon Canister Solenoid Valve for Haval H2 -
In the braking system of a car, the brake pad is the most critical safety part, and the brake pad plays a decisive role in the quality of all braking effects, so it is said that a good brake pad is the protector of people and cars. -
The brake disc is the friction couple of the disc brake. In addition to the strength and rigidity required as a component, it should also have a friction coefficient as high and stable as possible, as well as appropriate wear resistance, heat resistance and heat dissipation. and heat capacity, etc. . The brake disc needs to be replaced once every 70,000 kilometers. -
Sale!
The generator belt should generally be replaced when the car travels 60,000 to 80,000 kilometers, and a small number of cars can be replaced after 100,000 kilometers. We recommend it should not exceed 80,000 kilometers at most. -
1. The air filter is the core component of the filter. It is made of special materials and is a wearing part, which requires special maintenance and maintenance; 2. When the air filter has been working for a long time, the filter element has intercepted certain impurities, which will lead to an increase in pressure and a decrease in flow. At this time, it needs to be cleaned in time; 3. When cleaning, be careful not to deform or damage the filter element. -
A high-quality air conditioner filter can absorb powder tip particles, relieve respiratory pain, reduce irritation to allergy sufferers, make driving more comfortable, and protect the air conditioning cooling system. Please note that there are two types of air-conditioning filter elements, one without activated carbon and the other with activated carbon (consult before purchasing). The air-conditioning filter element containing activated carbon not only has the above functions, but also absorbs a lot of odors, etc. effect. The air-conditioning filter element is generally replaced every 10,000 kilometers.
